Extreme Networks Summit WM Series Uživatelská příručka Strana 90
- Strana / 228
- Tabulka s obsahem
- KNIHY
Hodnocené. / 5. Na základě hodnocení zákazníků
WM Access Domain Configuration
Summit WM-Series WLAN Switch and Altitude Access Point Software Version 1.0 User Guide
90
Once a wireless device user has logged in on the Captive Portal page, and has been authenticated by
the RADIUS server, then the following filters will apply:
● Filter ID Filter, if a Filter ID associated with this user was returned the authentication server
● Default Filter, if no matching Filter ID was returned from the authentication server
These filters are described below.
Filtering rules for a Filter ID group
The next step is to define the filtering rules for the Filter ID values on the WM-AD.
When the wireless device user enters a login identification, that identification is sent by the Summit
WM-Series Switch to the RADIUS server or other authentication server, through a sequence of
exchanges depending on the type of authentication protocol used.
When the server allows this request for authentication (sends an “access-accept” message), the RADIUS
server may also send back to the Summit WM-Series Switch a Filter ID attribute value associated with
the user. For an AAA WM-AD, a Login-LAT-Group identifier for the user may also be returned.
If the Filter ID attribute value (or Login-LAT-Group attribute value) from the RADIUS server matches a
Filter ID value that you have set up on the Summit WM-Series Switch, the Summit WM-Series Switch
applies to the wireless device user the filtering rules that you defined for that Filter ID value.
If no Filter ID is returned by the authentication server, or no match is found on the Summit WM-Series
Switch, then the filtering rules in the Default Filter will apply to the wireless device user.
- Table of Contents 3
- Formatting conventions 10
- Documentation feedback 10
- Protocols and standards 11
- Regulatory information 11
- About this Guide 12
- Conventional wireless LANS 13
- Wireless AP 15
- Summit WM 15
- Wireless Controller 15
- Network traffic flow 18
- Network security 19
- Policy: packet filtering 21
- Mobility and roaming 21
- Availability 22
- Quality of Service (QoS) 22
- Data ports (4 or 2) 24
- Management ports 24
- Configuration steps: overview 31
- Enabling the product key 31
- Setting up the data ports 32
- Port Type or Function 34
- Setting up static routes 35
- Setting up OSPF Routing 36
- Define port exception filters 40
- 4 Altitude AP: startup 41
- Installing the Altitude APs 43
- Set the discovery timers 45
- Discovery and registration 46
- Registration after discovery 48
- Altitude AP access approval 49
- ● 802.11 b/g (2.4 GHz radio) 53
- ● 802.11a (5 GHz radio) 53
- Adding a Altitude AP manually 56
- Auto Cell software 58
- Configure Auto Cell software 59
- Altitude AP: startup 60
- Introduction 61
- What is a WM-AD? 62
- Topology of a WM-AD 62
- Filtering for a WM-AD 64
- Setting up a new WM-AD 66
- Global Settings for a WM-AD 68
- Topology for a WM-AD 71
- Use DHCP Relay for the WM-AD 74
- Topology for a WM-AD for AAA 75
- Authentication for a WM-AD 76
- ● No Captive Portal Support 80
- Captive Portal” on page 87) 81
- Accounting for a WM-AD 84
- RADIUS Policy for a WM-AD 84
- Filtering rules for a WM-AD 86
- Default Filter: Examples 93
- Multicast for a WM-AD 95
- Privacy for a WM-AD 96
- Privacy for a WM-AD for AAA 97
- A WM-AD for voice traffic 101
- Availability and Mobility 103
- Management users 111
- Network time 112
- Check Point event logging 113
- Setting up SNMP 115
- Setting SNMP Parameters 116
- Overview 123
- Summit Spy: running scans 125
- The Analysis Engine 126
- 11 Ongoing operation 131
- Altitude AP client management 133
- Client disassociate 134
- Client blacklist 135
- Health Checking 136
- Change the system log level 136
- Enable and configure Syslog 136
- Logs and alarms 141
- View the Logs 142
- View the Traces 142
- View the Audits 143
- Reports and displays 144
- View reports 146
- Glossary 147
- D (Continued) 149
- F (Continued) 151
- H (Continued) 152
- I (Continued) 153
- O (Continued) 156
- P (Continued) 157
- S (Continued) 160
- T (Continued) 162
- W (Continued) 164
- Altitude AP system states 168
- B CLI command reference 169
- CLI command reference 170
- RFC list 177
- 802.11 standards list 178
- Reference lists of standards 180
- E Support for Altitude AP 181
- F RADIUS Attributes 183
- RADIUS Accounting 184
- Account-Stop/Interim Packet 185
- Termination Codes 186
- G Logs and Events 187
- Logs and Events 188
- Critical 189
- CDR_COLLECTOR 191
- CONFIG_MANAGER 191
- EVENT_SERVER 192
- RADIUS_ACCOUNTING 194
- RADIUS_CLIENT 194
- RF_DATA_COLLECTOR 195
- RU_MANAGER 195
- SECURITY_MANAGER 196
- STARTUP_MANAGER 197
- STATS_SERVER 198
- ACCESSPOINT 200
- CPDP_AGENT_ID 203
- NSM_SERVER 205
- OSPF_SERVER 206
- PORT_INFO_J_MANAGER 206
- REDIR_ID 207
- H Regulatory Information 213
- Emissions 214
- FCC ID#: RJF-A3502 216
- Part 15 Unlicensed Antenna 217
- European Community 218
- European Spectrum Usage Rules 221
- Regulatory Information 222
- Declarations of Conformity 223
Související produkty a manuály pro Software Extreme Networks Summit WM Series
Software Extreme Networks WM20 Controller Specifikace
(170 stránky)
(170 stránky)
Software Extreme Networks Ridgeline Guide Specifikace
(376 stránky)
(376 stránky)
© 2020, manymanuals.cz. Všechna práva vyhrazena. | 0.113 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Komentáře k této Příručce