Extreme Networks Summit WM Series Uživatelská příručka Strana 106
- Strana / 228
- Tabulka s obsahem
- KNIHY
Hodnocené. / 5. Na základě hodnocení zákazníků
Summit WM-Series Switch Configuration: Availability and Mobility
Summit WM-Series WLAN Switch and Altitude Access Point Software Version 1.0 User Guide
106
View the SLP activity with the “slpdump tool”
1 In the Altitude AP Registration Mode screen, click on the View SLP Registration button. A popup
screen displays the results of the diagnostic “slpdump tool”, to confirm SLP registration.
In normal operations, the primary Summit WM-Series Switch registers as an SLP service called
“ac_manager” and directs the Altitude APs to the appropriate Summit WM-Series Switch of a pair.
During an outage, if the remaining Summit WM-Series Switch is the secondary one, it will register as
an SLP service “ru_manager”.
Events and actions during a Failover
If one of the Summit WM-Series Switches in a pair fails, the connection between the two Summit WM-
Series Switches is lost. This triggers a “Failover mode” condition, and a critical message appears in the
information log of the remaining Summit WM-Series Switch.
After the Altitude AP on the failed Summit WM-Series Switch loses its connection, it will attempt a
reboot. Because of the pairing of the two Summit WM-Series Switches, the Altitude AP will then
register with the other Summit WM-Series Switch.
NOTE
A Altitude AP connects first to a Summit WM-Series Switch registered as “ac_manager” and, if not found, then
seeks an “ru_manager”. If the primary Summit WM-Series Switch fails, the secondary one registers as
“ru_manager”. This enables the secondary Summit WM-Series Switch to be found by Altitude APs after they reboot.
When the Altitude APs connect to the second Summit WM-Series Switch, they will be assigned to the
Failover WM-AD defined in setup in that Summit WM-Series Switch. The wireless device users will log
in again and be authenticated on the second Summit WM-Series Switch.
When the failed Summit WM-Series Switch recovers, each Summit WM-Series Switch in the pair goes
back to normal mode. They exchange information that includes the latest lists of registered Altitude
APs. The administrator will release the Altitude APs on the second Summit WM-Series Switch, so that
they may re-register with their home Summit WM-Series Switch.
- Table of Contents 3
- Formatting conventions 10
- Documentation feedback 10
- Protocols and standards 11
- Regulatory information 11
- About this Guide 12
- Conventional wireless LANS 13
- Wireless AP 15
- Summit WM 15
- Wireless Controller 15
- Network traffic flow 18
- Network security 19
- Policy: packet filtering 21
- Mobility and roaming 21
- Availability 22
- Quality of Service (QoS) 22
- Data ports (4 or 2) 24
- Management ports 24
- Configuration steps: overview 31
- Enabling the product key 31
- Setting up the data ports 32
- Port Type or Function 34
- Setting up static routes 35
- Setting up OSPF Routing 36
- Define port exception filters 40
- 4 Altitude AP: startup 41
- Installing the Altitude APs 43
- Set the discovery timers 45
- Discovery and registration 46
- Registration after discovery 48
- Altitude AP access approval 49
- ● 802.11 b/g (2.4 GHz radio) 53
- ● 802.11a (5 GHz radio) 53
- Adding a Altitude AP manually 56
- Auto Cell software 58
- Configure Auto Cell software 59
- Altitude AP: startup 60
- Introduction 61
- What is a WM-AD? 62
- Topology of a WM-AD 62
- Filtering for a WM-AD 64
- Setting up a new WM-AD 66
- Global Settings for a WM-AD 68
- Topology for a WM-AD 71
- Use DHCP Relay for the WM-AD 74
- Topology for a WM-AD for AAA 75
- Authentication for a WM-AD 76
- ● No Captive Portal Support 80
- Captive Portal” on page 87) 81
- Accounting for a WM-AD 84
- RADIUS Policy for a WM-AD 84
- Filtering rules for a WM-AD 86
- Default Filter: Examples 93
- Multicast for a WM-AD 95
- Privacy for a WM-AD 96
- Privacy for a WM-AD for AAA 97
- A WM-AD for voice traffic 101
- Availability and Mobility 103
- Management users 111
- Network time 112
- Check Point event logging 113
- Setting up SNMP 115
- Setting SNMP Parameters 116
- Overview 123
- Summit Spy: running scans 125
- The Analysis Engine 126
- 11 Ongoing operation 131
- Altitude AP client management 133
- Client disassociate 134
- Client blacklist 135
- Health Checking 136
- Change the system log level 136
- Enable and configure Syslog 136
- Logs and alarms 141
- View the Logs 142
- View the Traces 142
- View the Audits 143
- Reports and displays 144
- View reports 146
- Glossary 147
- D (Continued) 149
- F (Continued) 151
- H (Continued) 152
- I (Continued) 153
- O (Continued) 156
- P (Continued) 157
- S (Continued) 160
- T (Continued) 162
- W (Continued) 164
- Altitude AP system states 168
- B CLI command reference 169
- CLI command reference 170
- RFC list 177
- 802.11 standards list 178
- Reference lists of standards 180
- E Support for Altitude AP 181
- F RADIUS Attributes 183
- RADIUS Accounting 184
- Account-Stop/Interim Packet 185
- Termination Codes 186
- G Logs and Events 187
- Logs and Events 188
- Critical 189
- CDR_COLLECTOR 191
- CONFIG_MANAGER 191
- EVENT_SERVER 192
- RADIUS_ACCOUNTING 194
- RADIUS_CLIENT 194
- RF_DATA_COLLECTOR 195
- RU_MANAGER 195
- SECURITY_MANAGER 196
- STARTUP_MANAGER 197
- STATS_SERVER 198
- ACCESSPOINT 200
- CPDP_AGENT_ID 203
- NSM_SERVER 205
- OSPF_SERVER 206
- PORT_INFO_J_MANAGER 206
- REDIR_ID 207
- H Regulatory Information 213
- Emissions 214
- FCC ID#: RJF-A3502 216
- Part 15 Unlicensed Antenna 217
- European Community 218
- European Spectrum Usage Rules 221
- Regulatory Information 222
- Declarations of Conformity 223
Související produkty a manuály pro Software Extreme Networks Summit WM Series
Software Extreme Networks WM20 Controller Specifikace
(170 stránky)
(170 stránky)
Software Extreme Networks Ridgeline Guide Specifikace
(376 stránky)
(376 stránky)
© 2020, manymanuals.cz. Všechna práva vyhrazena. | 0.110 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Komentáře k této Příručce