Extreme Networks WM20 Controller Uživatelská příručka Strana 39
- Strana / 270
- Tabulka s obsahem
- KNIHY
Hodnocené. / 5. Na základě hodnocení zákazníků
Performing the First-Time Setup of the Summit WM Controller
Summit WM20 User Guide, Software Release 4.2 39
NOTE
All images of the Summit WM GUI in this User Guide represent the Summit WM Controller WM20. In the footer
of the Summit WM GUI, the following is displayed:
• [host name | product name | up time]
For example, [ Summit WM20| 7 days, 20:42].
• If there is no key (unlicensed), the product name will not be displayed.
• User is the user id you used to login in. For example, admin.
• Port Status is the connectivity state of the port. M represents the Management interface, which is on eth0 and
the numbered lights reflect the esa ports on the system. Green indicates the interface is up and running. Red
indicates the interface is down.
7 From the main menu, click Summit Switch Configuration. The Summit WM Controller
Configuration screen is displayed.
8 In the left pane, click IP Addresses. The factory default settings for the Summit WM Controller are
displayed.
9 In the Management Port Settings section, click Modify. The System Port Configuration screen is
displayed.
- Summit WM20 User Guide 1
- Table of Contents 3
- Formatting Conventions 10
- Documentation Feedback 10
- Safety Information 11
- Installing Power Supply Units 12
- Power Input Requirements 12
- Maintenance Safety 13
- General Safety Precautions 13
- Power Supply Cords Selection 13
- WARNING! 15
- Sicherheitshinweise 16
- Installation von Netzteilen 17
- Wartungssicherheit 17
- Auswahl der Stromkabel 18
- About this Guide 20
- Points and Software Solution 21
- ● Summit WM Controller 22
- ● Wireless APs 22
- Network Traffic Flow 25
- Network Security 26
- Authentication 27
- WM Access Domain Services 28
- Packet Filtering Policy 29
- Mobility and Roaming 29
- Network Availability 29
- System Configuration Overview 30
- Configuring for Remote Access 36
- Controller 37
- Setting up the Data Ports 42
- ● Third-Party AP Port 43
- ● Router Port 43
- Setting up Static Routes 45
- Setting up OSPF Routing 47
- Access Points and Software 53
- 3 Configuring the Wireless AP 55
- Wireless AP Radios 56
- Wireless AP Discovery 57
- Registration After Discovery 58
- Security Mode 60
- Discovery Timers 61
- ● Number of retries 62
- ● Delay between retries 62
- ● PoE enabled switch port 63
- ● PoE Injector 63
- ● Power by AC adaptor 63
- Default AP Configuration 79
- Copy to Defaults Feature 79
- Upgrade settings 84
- 4 WM Access Domain Services 85
- Setting up a WM-AD Checklist 86
- Topology of a WM-AD 87
- RF Assignment for a WM-AD 88
- Filtering for a WM-AD 90
- Final Filter Rule 91
- Filtering Sequence 91
- WM-AD Global Settings 92
- Setting up a New WM-AD 95
- Topology for a WM-AD 98
- Enabling Management Traffic 100
- To create an AAA topology: 105
- ● WM20 – Up to 8 WM-ADs 106
- Authentication for a WM-AD 108
- ● No Captive Portal Support 113
- ● AP Serial number 115
- ● AP Name 115
- ● WM-AD Name 115
- ● MAC Address 115
- ● WM-AD’s 118
- ● Select IP/Port 124
- ● DNS (IP of DNS server) 125
- ● Allows only HTTP traffic 127
- Default Filter Examples 131
- ● 64-bit 135
- ● 128-bit 135
- ● 152-bit 135
- Privacy for a WM-AD for AAA 137
- Table 12: Service Classes 142
- QoS Modes 143
- Table 15: Queues 144
- CS7 7/7 AF32 4/4 146
- Bridging Traffic Locally 148
- ● Untagged 149
- Availability Overview 151
- Availability Prerequisites 152
- Viewing SLP Activity 155
- Defining Management Users 157
- Configuring Network Time 158
- To apply time zone settings: 159
- To set Network Time Protocol: 159
- Enabling SNMP 162
- To enable SNMP Parameters: 163
- Using Controller Utilities 164
- To set up third-party APs: 169
- Working With Third-Party APs 172
- Summit WM Series Spy Overview 173
- ● Scan Groups 175
- ● Friendly APs 175
- ● Third-party APs 175
- ● AP Maintenance 175
- Analysis Engine Overview 176
- Working With Friendly APs 179
- To add friendly APs manually: 180
- To delete a friendly AP: 180
- To modify a friendly AP: 180
- To maintain the Wireless APs: 181
- Viewing the Displays 185
- To view reports and displays: 186
- Displays 189
- Viewing Reports 190
- To view reports: 191
- Disassociating a Client 195
- Blacklisting a client 196
- To change the log levels: 200
- To set a poll interval: 201
- Maintenance 202
- To upload a new backup: 207
- To delete a backup: 207
- To schedule a backup: 207
- To download for restore: 209
- To upload an image file: 210
- Logs and Traces 211
- To view logs: 212
- To view traces: 213
- To view audits: 214
- To clear logs: 215
- Performing System Maintenance 216
- Glossary 217
- D (Continued) 219
- I (Continued) 223
- M (Continued) 225
- N (Continued) 226
- O (Continued) 227
- P (Continued) 228
- R (Continued) 229
- S (Continued) 230
- V (Continued) 234
- Terms and Abbreviations 235
- A Summit WM20 Controller 237
- Summit WM20 Controller Panels 238
- Summit WM20 Controller’s LEDs 239
- B Regulatory Information 241
- EMI/EMC Standards 242
- Environmental Conditions 242
- Operational Environment: 243
- Detach. AP (15939) 244
- FCC ID#: RJF-A3502A 245
- Part 15 Unlicensed Antenna 246
- European Community 247
- European Union 1999/5/EC 248
- European Spectrum Usage Rules 250
- Declarations of Conformity 252
- Detach. (15939) Access Points 253
- Antenna Diversity 254
- Regulatory Information 256
- RF Safety Distance 258
- Professional Installation 258
Související produkty a manuály pro Software Extreme Networks WM20 Controller
Software Extreme Networks Ridgeline Guide Specifikace
(376 stránky)
(376 stránky)
Software Extreme Networks Summit WM Series Specifikace
(140 stránky)
(140 stránky)
© 2020, manymanuals.cz. Všechna práva vyhrazena. | 0.059 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Komentáře k této Příručce