Extreme Networks Summit WMScanner Uživatelská příručka Strana 41
- Strana / 217
- Tabulka s obsahem
- KNIHY
Hodnocené. / 5. Na základě hodnocení zákazníků
Summit WMScanner Users Guide 39
existing layer. The Layer Properties Manager also allows you to create new layers by using the New
button in the Layer Properties Manager dialog box. You can also select a particular layer and make it the
current layer by clicking the Current button.
Lineweight Settings
Lineweight Settings are useful for increasing the thickness with which lines are drawn in 2D Wireframe
and other wireframe views. It is not common to use the 2D Wireframe view; the Flat Shaded, Edges On
view is more commonly used, as it has filled in walls that provide a more realistic 3D appearance.
However, when in 2D Wireframe mode, thicker lines can help make the walls of a building stand out
over a bitmap background.
To use typical settings for displaying lineweights, check the Display Lineweights checkbox in the
Lineweight Settings dialog box, and choose 0.30mm from the Default combo box. Make sure that your
Lineweights list box has ByLayer selected. Click OK in the Lineweight Settings dialog box to close it and
display the increased lineweights. Note that the lineweights will only be visible in wireframe modes.
Lineweights do not affect RF propagation simulation.
Prune Overlapping Partitions
This command process the design removing overlapping partitions to prevent double/triple attenuation
of partitions. Overlapping partitions are lines that get drawn directly on top of each other. Because
Summit WMScanner treats each line as a wall, the effect of overlapping lines is that two walls are
recognized where there should only be one. Prune overlapping partitions removes the duplicate lines so
long as they are the same partition type and drawn with the same start and end point.
Break/Ungroup Entities
This command ungroups individually selected grouped blocks in the current viewport. This means that
any grouped blocks that are currently being displayed will be separated (ungrouped) if you select them.
- WMScanner User Guide 1
- Summit WMScanner Users Guide2 2
- Table of Contents 3
- Summit WMScanner Users Guide4 6
- 1 Summit WMScanner Overview 7
- Preparation 8
- Driver Installation 9
- Summit WMScanner Overview 10
- Hardware Removal 12
- Activating Your Software 14
- Applying Your Activation Code 15
- Determining Your Version 15
- Wireless Network Basics 18
- Before Getting Started 19
- Import Site-Specific Drawing 19
- Exporting Drawings to WMS 20
- 2 WMScanner GUI and Menus 21
- Toolbar Icons 22
- Hot Keys 23
- Legend Window 24
- WMScanner Menus 25
- Editing a Color Scheme 28
- Scale Floor Plan 28
- View Menu 29
- View Menu - Building Floor 30
- View Menu - Shade 32
- WMScanner GUI and Menus 34
- Format Building Menu 35
- Edit Sub-menu 37
- Advanced Sub-menu 38
- Building Manager 38
- Drawing Limits 39
- Layer Properties Manager 39
- Lineweight Settings 41
- Prune Overlapping Partitions 41
- Break/Ungroup Entities 41
- Equipment Menu 42
- Measurement Survey Data 43
- Reports Menu 44
- Utilities Menu 51
- Project Information 52
- Setting the Project Workspace 52
- New Project Workspace 56
- Utilities - Drawing Legend 59
- Preferences Dialog 61
- Preferences - Display 62
- Preferences - Open and Save 64
- Preferences - Plotting 65
- Preferences - System 66
- Preferences - Drafting 68
- Preferences - Selection 70
- Help Menu 72
- 3 Measurement Surveys 75
- Taking Measurements 76
- Specifying Channel Width 79
- Setting Measurement Points 82
- Configure Visible Data 84
- Manual Data Entry 89
- AP Performance Mode 90
- Measurements” 98
- Visualizing Survey Data 102
- Visualization Panel 103
- Channel Visualization 107
- Coverage Visualization 108
- SNR Visualization 109
- SSID Visualization 110
- Shaded, Edges On) 111
- Noise Visualization 112
- Edges On) 114
- Channel Width Performance 116
- Data Rate Performance 117
- Measurement Surveys 118
- Verifying Network Coverage 119
- Deleting Measurement Data 123
- Access Point Associations 124
- Display Measurement Data 126
- Text Display 127
- Set Text Height 128
- Graphical Display 128
- Managing Access Points 132
- Access Point Placement 133
- Edit/Remove Access Point 136
- Access Point Colors 142
- Move Access Point 143
- Copy Access Point 144
- Clone Attributes 145
- Network Controllers 146
- Editing/Removing Controllers 147
- Edit Controller 148
- Managing Sensors 149
- Placing Sensors 150
- Editing/Removing Sensors 151
- Moving Sensors 153
- Copying Sensors 153
- Managing RFID Devices 154
- Placing RFID 155
- Editing/Removing RFID Devices 156
- Editing RFID 157
- Adding/Editing the Antenna 159
- Reference Tags 160
- Editing Reference Tag 163
- ■ The Reference Code Field: 164
- 4 Model Building 167
- Using the Building Wizard 168
- Leave Floor Empty 173
- Sketch Floor Plan 173
- Model Building 174
- Formatting Wizard 174
- Making a Copy of a Floor 178
- Importing an Unformatted File 178
- Import Preformatted File 182
- Rescale Floor 184
- Reset Floor Alignment Point 184
- Draw New Partitions 184
- Importing Images Using Insert 185
- Drawing Zones 187
- Adding Zones 189
- Editing/Removing Zones 190
- Defining Zone Colors 192
- Show/Hide All Zones 194
- Format CAD Drawing 194
- Drawing Partitions 198
- Change Partition 201
- Current Partition Categories 202
- Editing the Partition Library 205
- Categories” on page 200) 207
- 2D and 3D 210
- Viewing In 3D 212
- A Customer Support 215
- Customer Support 216
Související produkty a manuály pro Software Extreme Networks Summit WMScanner
Software Extreme Networks Ridgeline Guide Specifikace
(376 stránky)
(376 stránky)
Software Extreme Networks Summit WM Series Specifikace
(140 stránky)
(140 stránky)
Steelcraft-automotive 240710 3 ROUND SIDE BAR manuals
Owner’s manuals and user’s guides for For the car Steelcraft-automotive 240710 3 ROUND SIDE BAR.
We providing 1 pdf manuals Steelcraft-automotive 240710 3 ROUND SIDE BAR for download free by document types: User Manual
Komentáře k této Příručce